How do I fix E6 error on Fisher and Paykel dishwasher?

How do I fix E6 error on Fisher and Paykel dishwasher?

Fisher and Paykel Dishwasher Dishdrawer Error Code E6 = The first 4 program indicator lights are flashing. Error Code Cause: Flood switch activated. How To Fix: Turn the water and power off to the dishwasher and back on to try and reset. Check Flood Switch.

How do I reset my Fisher Paykel dishwasher?

Reset Procedures for the Fisher & Paykel Dishwasher

1. Press the power button to turn off power to the Fisher & Paykel dishwasher.
2. Wait a few minutes and then press the power button to restore power.
3. Turn off and unplug the dishwasher if the issue remains.
4. Wait five minutes and restore power to the unit.

What does E6 mean on a dishwasher?

An E6 error code of the Bosch dishwasher means that there are problems with the sensor that controls the water turbidity. It is also called the Aqua Sensor. In the dishwasher, this sensor detects the turbidity of the water due to the presence of small particles of dirt, food residues and other things inside it.

How do you clear a dishwasher error code?

The Fix: Pressing and holding the cancel button or turning off the power to the dishwasher for five minutes should clear the error code. If the error persists, you will need to troubleshoot the water heating system or call a professional to fix the issue.

Why is my Fisher and Paykel dishwasher not draining?

Straighten any kinks along the hose that drains water from your DishDrawer™. If the kinks return, you may need to replace the hose. Clean the filter plate/drain filter. Aim to clean your DishDrawer™ at least once per month, including the drain filter plates.

How do you run a diagnostic on a Fisher Paykel dishwasher?

Diagnostic Mode. With Power off, press/hold Keylock, then press Start/Pause at the same time for 5 seconds. Release the buttons when it powers-on. Press Power once.

Why does my Fisher Paykel dishwasher keep beeping?

The drainage hose may be blocked or kinked, or the connection to drainage pipe may be blocked. Ensure the drainage hose and connection to pipes are not blocked. once to stop the beeping, and then again to clear the fault. to resume the wash program.

How do I fix Fisher and Paykel dishwasher f1 error?

1. Locate the drain-access filter panel on the bottom of the drawer.
2. Remove the rack that sits above it.
3. Pull up to lift the drain filter and remove it from the machine.
4. Set the filter under the faucet to rinse it clean with cold water.
5. Reinstall the filter and confirm that it sits flush with the bottom of the DishDrawer.

How do I reset my dishwasher?

To reset a dishwasher, you need to hold the start button down for three seconds or, failing that, switch your dishwasher off at the main power supply. If that won’t sort out the glitch, you may have problems with your power, water source, door latch, or internal issues.

What does the snowflake symbol mean on dishwasher?

Snowflake like symbol is for Rinse-aid and, paper clip like symbol is for Salt Refill. Please could you check for salt and rinse-aid. If rinse-aid and salt LEDs are still ON then unplug the dishwasher for 2-3 minutes or reset the circuit breaker, plug it back and check.

How do you unclog a Fisher and Paykel DishDrawer drain?

Straighten the hose and look through it. If you can see obstructions, the drain hose is likely the cause of your drainage problems. Flush out all of the debris with very hot water from the sink, then replace the drain hose, tightening it well at both connection points.

How to check for a DW60 dishwasher fault?

DW60 Dishwasher Fault Code Explanation E1 or F1 Door alarm – check that the door is clos E2 Sensor alarm – Y ou will require a Servi E3 or F3 Drain hose fault, check the drain hose i E4 or F4 Drain fault, check the drain hose is not

What to do if your Fisher and Paykel dishwasher is not working?

Press again to turn the dishwasher back on. If the dishwasher still does not function and/or the problem persists, disconnect the dishwasher from the power supply, turn the water supply off, then contact Fisher & Paykel Customer Care with the fault code information. Drain hose is crimped or bent.

What is the error code for the F and P dishwasher?

The following error codes are for the F&P dishwasher models DS603, DD603, DD24, DD60, DD36, and DD90. Click on the link to view the PDF file.

What to do if your dishwasher has a fault?

Flood switch activated. Turn the dishwasher OFF and ON again. If fault persists, turn water off and disconnect the dishwasher from the power supply. Call Customer Care. Water flow error. Switch dishwasher OFF and ON again. If fault persists call Customer Care. Electronics error. Switch dishwasher OFF and ON again.