Table of Contents
- 1 What size is the transmission fill plug?
- 2 What size socket do I need to change transmission fluid?
- 3 How much fluid does a manual transmission hold?
- 4 How much transmission fluid does a 1990 Miata take?
- 5 How much does a 1991 Miata weigh?
- 6 How many quarts does it take to fill a transmission?
- 7 When to install oil seal retainer on Isuzu engine?
- 8 Where is the drain plug on an Isuzu Rodeo?
- 9 What is the p0138 code on an Isuzu troque?
What size is the transmission fill plug?
Transmission fill plug is a 9/16ths” square, a standard plumbing size.
What size socket do I need to change transmission fluid?
It looks like a breaker bar with an adaptor that would be used to connect 1/2” drive tools to 3/8” sockets. The drain plug is simply a 3/8” square so any extension with a 3/8” inch square will work. You don’t need a special tool.
How much fluid does a manual transmission hold?
While the type and exact amount of transmission fluid are dependent on the model of the vehicle, most passenger vehicles take approximately 12 to 16 qts of transmission fluid.
What size Bolt is the oil drain plug?
Oil Drain Plug Standard M14-1.50, Head Size 17mm.
What is the most common oil drain plug size?
There are four common socket sizes: 1/4 inch (0.6 centimeters), 3/8 inch (0.9 centimeters), 1/2 inch (1.3 centimeters) and 3/4 inch (1.9 centimeters). In addition, sockets are available in various shapes to fit the different bolt heads: six points (hexagon), eight points (double square), and 12 points (double hexagon).
How much transmission fluid does a 1990 Miata take?
How much transmission fluid does a 1990 Miata take?
| Vehicle Identification | |
|---|---|
| Engine Oil | 3.4 US quart (3.2 L); with filter 3.58 US quart (3.4 L) |
| Engine Oil Weight | 10W-30 |
| Manual Trans. Fluid | 2.1 US quart (2.0 L) |
| Trans. Fluid Weight | 80W-90 |
How much does a 1991 Miata weigh?
2182 lbs.
Used 1991 Mazda MX-5 Miata Specs & Features
| Dimensions | |
|---|---|
| Curb weight | 2182 lbs. |
| Height | 48.2 in. |
| Length | 155.4 in. |
| Wheel base | 89.2 in. |
How many quarts does it take to fill a transmission?
In general, transmissions take about 9 to 13 quarts to fill completely. The amount of transmission you add will vary, depending on whether you are draining or replacing it all or you are just topping it up. Again, you should avoid adding too much. It is advisable to put in little amounts at a time.
What fluid goes in manual transmission?
Manual transmissions use a variety of oils: regular motor oil, heavyweight hypoid gear oil or even automatic transmission fluid in some cases. Your owner’s manual will tell you what your transmission calls for.
When to change transmission fluid in an Isuzu Rodeo?
Transmission fluid is an essential lubricant for any automobile. It keeps the transmission’s moving parts lubricated and cooled. But transmission fluid breaks down over time, and when it does it cannot protect the moving parts as it should. Isuzu recommends you change the fluid in your Rodeo’s transmission after 50,000 to 75,000 miles of wear.
When to install oil seal retainer on Isuzu engine?
The Left Photo Above Shows Rear Oil Seal Retainer The oil seal retainer must be installed within 5 minutes after sealant application before the sealant hardens The Middle Photo Shows Rear Oil Seal Retainer. The Left Photo shows the other side of oil seal.
Where is the drain plug on an Isuzu Rodeo?
The drain plug is in the middle of the transmission on the bottom. The fill plug is about 6 inches to the rear of the drain plug; it will be inside a recessed groove on the rear of the oil pan. Remove the fill plug on the rear passenger side of the transmission with the ratchet and 7/8-inch socket.
What is the p0138 code on an Isuzu troque?
The P0138 code is set when the Engine Control Module (ECM) detects that the rear O2 sensor signal voltage remains excessively high for an extended period of time. TECH NOTES: Replacing the Rear Heated Oxygen Sensor Bank 1 usually takes care of the problem.