How far does a light switch need to be from a sink?

How far does a light switch need to be from a sink?

Every bathroom needs at least one electrical outlet. It must be within 3 feet of the sink edge. Across from the sink on an opposite wall is not acceptable, either behind or beside the sink. There must be an electrical receptacle within 3 feet of the two sinks in the bathroom.

Can a light switch be near a tub?

Switches shall not be installed within wet locations in tub or shower spaces unless installed as part of a listed tub or shower assembly. {NOTE: According to both the NEC and the IRC a damp/wet location is in the area within 36 inches of either edge of a tub sink or basin and/or an area that is subject to “spray”.

How close can an electrical outlet be to a bathroom sink?

Outlet Receptacles You should keep the receptacle at least 6 feet away from the edge of a bathtub or shower and at least 1 foot away from sinks.

Can I install a light switch near a sink?

If it is a bathroom sink counter top, it can not be farther than 36″ from the edge of the sink. All kitchen counter top and bathroom receptacles are required to be GFCI protected regardless of distance of the sink. Receptacles within 6′ of a wet bar or laundry tub are required to be GFCI protected.

Where should a light switch be placed in a bathroom?

For light switches, plate switches can be used on the inside of the bathroom, but these must be suitable for use in the bathroom, given the high levels of humidity and condensation. And they also must be at least 0.6m away from the bath or shower. A pull cord can be used instead, in any location in the bathroom.

How close can a light fixture be to a shower?

The 2011 National Electric Code requires at least eight feet of space between the top of the tub or shower base and the bottom of the chandelier. This “no chandelier zone” also extends three feet outside of the tub or shower stall area.

How far does a GFCI have to be from a sink?

6 ft.
Generally, all 15 or 20-amp, single phase, 125-volt receptacles “within 6 ft.” of a sink, tub or shower must be GFCI protected. For a sink, the measurement starts “from the top inside edge of the bowl of the sink”. For a bathtub or shower, the measurement starts at “the outside edge of the bathtub or shower stall”.

How far does a GFCI have to be from water?

6 feet
According to the National Electric Code, any receptacle within 6 feet of a water source needs to be protected with a GFCI.

How far off the floor should an electrical outlet be?

Standard Height for Outlet Boxes The standard height for wall outlet boxes is about 12 inches from the top of the floor covering to the bottom of the receptacle box (or 16 inches to the top of the box).

How tall should a light switch be from the ground?

The ideal light switch height is 48 inches from the ground. Builders generally use this standard since this height can be reached as comfortably from the standing position as from the sitting position.

How close can I put a switch or outlet from a sink?

You can place a switch and receptacle as close to the sink as you want. There are a few other rules you may need to follow: If it is a kitchen counter, the receptacles must be places so that no portion of the counter top is farther then 24″ from a receptacle (commonly called the 2’/4′ rule)

What does CEC 30-320 ( C ) say about light switches?

CEC 30-320 (c) said: Switches (including wall switches) controlling luminaires covered by Subrules (1) and (2) shall (a) be located not less than 1 m from a bathtub or shower stall (this distance measured horizontally between the switch and the bathtub or shower stall) without piercing a wall, partition, or similar obstacle; or

Can you put a sink switch on the counter top?

You can place a switch and receptacle as close to the sink as you want. There are a few other rules you may need to follow: If it is a bathroom sink counter top, it can not be farther than 36″ from the edge of the sink.

https://www.youtube.com/watch?v=NfRuLlTp5s8