How do you fix a C1 error on a washing machine?

How do you fix a C1 error on a washing machine?

Resolution

1. Check the water supply to ensure that the water pressure is proper.
2. Clean the filter in the inlet hose next to the tap.
3. Ensure correct position of the drain hose.
4. Ensure correct drain height.
5. Clean the pump and filter.
6. Check for blocked drain.
7. Check the drainage hose/inlet hose for possible kink or twist.

How do I fix the error on my Whirlpool washing machine?

An LE error code on the washer’s display indicates that the motor is locked, possibly due to a heavy wash load. Large and heavy sized loads will put a strain on the motor, causing the LE code to occur. Performing a reset on the washer will normally resolve this error with a reduced load size.

How can I reset my Whirlpool washing machine?

Method 1: Unplug it The first way you can reset whirlpool washer top load is by unplugging it for about 2 minutes then plug it back in and wait about 30 seconds before starting the washer again. This performs a hard reset on the machine and it will start over after you reconnect it again.

What is C1 on Whirlpool Cabrio washer?

The C1 error is displayed when the motor tries to pull more than 26 amps to run. This indicates a problem with the motor or motor controller. Overloading or excessive suds can also cause this error but you say the error comes up even if the washer is empty.

What does the letter F 35 mean on Whirlpool washing machine?

The F35 error code in the Whirlpool washer indicates some problems with the water level pressure switch. The more the tank is filled, the higher the pressure becomes. The level sensor signals the control module that it is time to fill the tank with water.

How do you clear the error code on a Whirlpool top load washer?

System error code. Press START/PAUSE once to clear the code, then press START/PAUSE again to restart washer. If the code doesn’t clear, Contact Us or Schedule Service Online. Hot and cold inlet hoses have been installed incorrectly (reversed).

What is error code PE in Whirlpool washing machine?

PE. Of all the Whirlpool washing machine error codes, PE is one that may require a professional repair. This code usually indicates a problem with the pressure level sensor. This sensor monitors how much water is in the machine, also telling the control board if it’s been filled or emptied.

How do I reset my Whirlpool top load washer?

The first means to reset the top load of the whirlpool washer is to unplug it for about 2 minutes, plug it in, and wait about 30 seconds until the washer starts again. This resets the machine hard and begins after you reconnect it again.

What does F32 mean on Whirlpool washer?

The Whirlpool Duet Washer F32 Error is a water level pressure switch failure code. If there is no voltage to the pressure switch from the central control unit or if the contacts in the pressure switch are worn out the central control will report this error and shut the cycle down.

When did the Whirlpool Calypso washing machine come out?

The Whirlpool Calypso Washing Machine was an early top loading energy saving washer produced in 2000-2001. It is a good washer design for the most part but is notorious for pump problems.

What do I do when my Whirlpool Calypso washing machine beeps?

Press STOP/CANCEL to clear the display. If the water fill time exceeds ten (10) minutes, the water valves are turned off and “LF” is flashed. Press STOP/CANCEL to clear the display. If there is any breakdown in communication between the machine controller and the motor controller, “CE” flashes and the unit beeps once.

What does Peekaboo mode on Whirlpool Calypso washer do?

The Lid switch is used to sense if the lid is closed and it is safe to proceed with the washing machine’s nutation and spin functions. The Calypso washer is equipped with a peekaboo mode that allows the washer to continue nutation for 5 seconds after the lid has been opened.