Table of Contents
- 1 How can I make sure my trailer height is correct before coupling?
- 2 What is coupling a trailer?
- 3 What should the trailer height be before you connect a converter dolly to a second or third trailer?
- 4 What will happen if the lines are crossed when you hook up to an old trailer?
- 5 What is the meaning and purpose of machine coupling?
- 6 How much space should be between the upper and lower fifth wheel coupling?
- 7 What should I look for when coupling a trailer?
- 8 What’s the best way to uncouple a trailer?
How can I make sure my trailer height is correct before coupling?
How do you check to make sure trailer height is correct before coupling? It must be slightly lower than the center of the fifth wheel, so trailer is raised slightly when dolly is pushed under.
When coupling a trailer you should raise the landing gear?
|After you have coupled the trailer you should have to raise the landing gear by using:||Low gear.|
|You supply air to the trailer tanks by:||Pushing in the trailer air supply valve.|
|Which part of the kingpin should the locking jaws close first?||The shank.|
What is coupling a trailer?
The coupling consists of a kingpin, a 2-or-31⁄2-inch-diameter (50.8 or 88.9 mm) vertical steel pin protruding from the bottom of the front of the semi-trailer, and a horseshoe-shaped coupling device called a fifth wheel on the rear of the towing vehicle. The advantage of this type of coupling is towing stability.
When coupling the proper position of the fifth wheel is?
When coupling, the proper position of the fifth wheel is: Tilted Down towards the end of the tractor. A trailer is most likely to jackknife when it is: Empty.
What should the trailer height be before you connect a converter dolly to a second or third trailer?
When connecting a converter dolly to a second or third trailer, the trailer height should correct. It should be slightly lower than the center of the fifth wheel.
What causes the crack the whip effect?
The crack a whip makes is produced when a section of the whip moves faster than the speed of sound creating a small sonic boom. The creation of the sonic boom was confirmed in 1958 by analyzing the high-speed shadow photography taken in 1927.
What will happen if the lines are crossed when you hook up to an old trailer?
To prevent steering problems. What will happen if the air lines are crossed when you hook up to an old trailer? If the trailer has no spring brakes, you could drive away but you would not have trailer brakes. Trailer emergency brakes to come on.
When backing up your tractor while coupling it to a trailer the trailer brakes should be?
Before backing your tractor under the trailer while coupling, make sure your trailer brakes are locked.
What is the meaning and purpose of machine coupling?
A coupling is a device used to connect two shafts together at their ends for the purpose of transmitting power. The primary purpose of couplings is to join two pieces of rotating equipment while permitting some degree of misalignment or end movement or both.
When should you uncouple a trailer?
The following steps will help you to uncouple safely.
- STEP 1: Position Rig.
- STEP 2: Ease Pressure on Locking Jaws.
- STEP 3: Chock Trailer Wheels.
- STEP 4: Lower the Landing Gear.
- STEP 5: Disconnect Air Lines and Electrical Cable.
- STEP 6: Unlock Fifth Wheel.
- STEP 7: Pull Tractor Partially Clear of Trailer.
- STEP 8: Secure Tractor.
How much space should be between the upper and lower fifth wheel coupling?
There should be no space between the upper and lower fifth wheel.
When you back a trailer you should position your vehicle?
When backing a trailer, you turn the steering wheel in the opposite direction. Once the trailer starts to turn, you must turn the wheel the other way to follow the trailer. Whenever you back up with a trailer, try to position your vehicle so you can back in a straight line.
What should I look for when coupling a trailer?
The trailer should be low enough that it is raised slightly by the tractor when the tractor is backed under it. Raise or lower the trailer as needed. (If the trailer is too low, the tractor may strike and damage the nose of the trailer; if the trailer is too high, it may not couple correctly.) Check that the kingpin and fifth wheel are aligned.
How to know if a tractor is coupled to a trailer?
Check that cargo (if any) is secured against movement due to tractor being coupled to the trailer. Put the tractor directly in front of the trailer (never back under the trailer at an angle because you might push the trailer sideways and break the landing gear). Check position, using outside mirrors, by looking down both sides of the trailer.
What’s the best way to uncouple a trailer?
Check position, using outside mirrors, by looking down both sides of the trailer. Back until fifth wheel just touches the trailer. Do not hit the trailer. Put on the parking brake. Put transmission in neutral. The trailer should be low enough that it is raised slightly by the tractor when the tractor is backed under it.
What should I do if my semi trailer collapses?
Stop with tractor frame under trailer (prevents trailer from falling to ground if landing gear should collapse or sink). Apply parking brake. Place transmission in neutral. Make sure ground is supporting trailer. Make sure landing gear is not damaged. Release parking brakes. Check the area and drive tractor forward until it clears.