Table of Contents
- 1 Can you get a mortgage with a dug well?
- 2 How do I find an existing water well?
- 3 How much does a dug well cost?
- 4 How deep should a dug well?
- 5 How much does it cost to dig a well?
- 6 How much does it cost to get a well dug?
- 7 How can I find out the depth of my well?
- 8 What was the first way to dig a well?
- 9 Where can I find a well on my property?
Can you get a mortgage with a dug well?
HUD 4000.1 (the FHA loan rule book) is the most current reference, and contains this section that references dug wells: FHA loan rules for appraisals often defer to local authorities or state/local standards in cases like these. The existence of dug wells may be acceptable in some housing markets but not in others.
How do I find an existing water well?
Clues to the location of these wells include:
- Pipes sticking out of the ground.
- Small buildings that may have been a well house.
- Depressions in the ground.
- The presence of concrete vaults or pits (perhaps covered by lumber or metal plates)
- Out-of-use windmills (wind pumps) are likely to be located near an old well.
How long do dug wells last?
Most wells have a lifespan of 20-30 years. Since sediment and mineral scale build up overtime, water output may wane over the years.
How much does a dug well cost?
Well Drilling Cost Drilling a well costs $5,500 for an average depth of 150 feet. Most projects range between $1,500 and $12,000. Expect to pay between $15 and $30 per foot of depth, or up to $50 for difficult terrain. Digging might be enough for shallow depths, ranging between $10 and $25 per foot.
How deep should a dug well?
To minimize water quality and quantity impacts, dug wells should be at least 3 m (10 ft) deep and sited away from surface water sources. Surface water can carry contaminants from the land surface into your well and the aquifer.
How do I find out about my well?
You can get the information from your well report. You can get the information from the company who drilled the well. You can get a copy of the well report from your state.
How much does it cost to dig a well?
Drilling a residential water well costs $25 to $65 per foot or $3,750 to $15,300 on average for a complete system and installation. Prices include the drilling, a pump, casing, wiring, and more. Total costs largely depend on the depth drilled and the well’s diameter.
How much does it cost to get a well dug?
How deep is a well dug?
10 to 30 feet deep
Since it is so difficult to dig beneath the ground water table, dug wells are not very deep. Typically, they are only 10 to 30 feet deep. Being so shallow, dug wells have the highest risk of becoming contaminated. To minimize the likelihood of contamination, your dug well should have certain features.
How can I find out the depth of my well?
This information can be useful in determining what the average depth is in your area. Simply look for several wells that are nearby. One way this data may be presented is a “water availability map” which shows how much groundwater availability there is for any one area, as well as the depth of that water.
What was the first way to dig a well?
Dug Wells. In the Coastal Plain, early wells were typically constructed by digging a hole just below the water table and lining it with bricks or pre-formed concrete rings. Water would be withdrawn either by bucket or by suction or jet pump. Dug wells typically had adequate supply for domestic or farm use,…
How is water withdrawn from a dug well?
Water would be withdrawn either by bucket or by suction or jet pump. Dug wells typically had adequate supply for domestic or farm use, but were susceptible to droughts and to surface contamination (such as septic tank effluent and pesticides).
Where can I find a well on my property?
City, Township, or County Officials – may have records of wells on a property, such as through building, water connection, or sewer permits. Municipal water department – may have record of when public water supply was provided to property.